APM 2730 is a high alloyed powder metallurgical high speed steel corresponding to ASTM M3:2 +Co with a combination of very good abrasive wear resistance, high compressive strength and good high temperature properties. Suitable areas of use include demanding cold-work applications like blanking of harder materials like carbon steel or cold-rolled strip steel, as well as use for cutting tools.
As with all powder metallurgy tool steels, machinability and grindability are superior to conventional high speed steel due to the very fine microstructure. Thanks to the fully homogenous material achieved in the powder metallurgy process, the dimensional stability after heat treatment is excellent. The process also ensures that the cleanliness of the steel is very high with a low amount of non-metallic inclusions. Compared to APM 2723 it has higher compressive strength and increased high temperature properties.
- M3:2 + Co
Chemical composition (nominal)
Forms of supply
Components can be supplied in a wide range of dimensions and shapes thanks to the flexibility provided by powder metallurgy and near net shape technology. The products are supplied in the soft annealed condition at approximately 300 HB.
Density: 8.104 g/cm3, 0.292 lb/in3
Mean coefficient of thermal expansion, 20-100°C: 10.1x10-6/°C
|Temperature, ºC||MPa||Temperature, ºF||ksi|
Protect the steel from decarburization and oxidation and heat to 850–900°C (1560–1650°F). Cool in the furnace at 10°C/h (20°F/h) to 700°C (1290°F), then freely in air.
After rough machining the tool should be heated to 600–700°C (1110–1290°F), holding time 2 hours. Cool slowly to 500°C (930°F), then freely in air.
Hardening and tempering
Pre-heating temperature: 450–500°C (840– 930°F) and 850–900°C (1560–1650°F). Austenitizing temperature: 1050–1180°C (1920–2160°F) according to the desired final hardness, see diagram below. The tool should be protected against decarburization and oxidation during hardening.
Quenching media can be high speed gas at 2-5 bars overpressure in vacuum furnace or forced air/gas. Quenching should be performed until the part reaches 50°C followed by immediate tempering.
For cold work applications tempering should always be carried out at 560°C (1040°F) irrespective of the austenitizing temperature. Temper three times for one hour at full temperature. The tool should be cooled to room temperature between the tempers. The retained austenite content will be less than 1% after this tempering cycle.
The diagram below shows hardness ±1 HRC vs. tempering temperature for different austenitizing temperatures.
APM 2730 can be worked as follows:
- Machining (grinding, turning, milling)
- Plastic forming
- Electrical Discharge Machining
Welding (special procedure including preheating and filler materials of base material composition).
During grinding, local heating of the surface, which may alter the temper, must be avoided. Grinding wheel manufacturers can furnish advice on the choice of grinding wheels. For grinding in hardened condition the use of CBN wheels is recommended.
Electric discharge machining - EDM
If EDM is performed in the hardened and tempered condition, finish with “fine-sparking”, i.e. low current, high frequency. For optimal performance the EDM’d surface should then be ground/polished to remove the white layer and the tool re-tempered at approx. 535°C (995°F).
The steel grade is a good substrate material for PVD and CVD coating. If nitriding is requested, a small zone of 2-15 µm is recommended. The steel grade can also be steam-tempered if so desired.
The cutting data below are to be considered as guiding values which must be adapted to existing local conditions. For more information on machining visit sandvik.coromant.com.
|Cutting speed m/min||80-110||110-140||10-15|
|Cutting depth, mm||2-4||0.5-2||0.5-3|
|Face milling||Cemented carbide|
|Cutting speed m/min||40-80||80-110|
|Cutting depth, mm||2-4||1-2|
|End milling||Cemented carbide|
|Cutting speed m/min||35-45||70-90|
|Square/shoulder milling||Cemented carbide|
|Cutting speed m/min||100-130||90-120||80-100|
|Drill size, mm||HSS||Coated HSS|
|Cutting speed, mm/min||Feed rate, mm/rev||Cutting speed, mm/min||Feed rate, mm/rev|
|Cutting data||Type of drill|
|Indexible insert Ø20-40 mm||Solid carbide Ø5-40 mm||Carbide tip Ø20-40 mm|
|Cutting speed m/min||100-130||50-70||25-35|